WinchPull

Winch line pull calculator for tow and recovery
by Tahuya River Software Tahuya River Software
Line tensionPulling uphill
0lb

Drag to set the slope

The job

Tap a line to change it. The readout updates as you go.

Examples

How winch line pull is figured

Line pull is the tension on the winch cable while you drag a casualty. It comes from the grade you're pulling against, the resistance of the ground and the vehicle's condition, and friction in every sheave the line runs through. Rigging more parts of line spreads that load, so each line carries less.

  1. Grade. Weight × sin(slope angle). Pulling uphill adds it; pulling downhill takes it away.
  2. Resistance. Weight × cos(slope angle) × the ground factor from the table below. If more than one applies, use the largest. They don't add together.
  3. Sheave friction. Add 10% of that load for each sheave: the boom sheave and every snatch block.
  4. Parts of line. Divide the total by the parts of line to get the tension on each line.

Worked example

A 13,000 lb casualty on a 5° slope of gravel, pulled uphill on a single line over the boom sheave:

Grade13,000 × sin 5°1,133 lb
Resistance13,000 × cos 5° × 15%1,943 lb
Net pullgrade + resistance3,076 lb
Sheave friction1 sheave × 10%308 lb
Line tension1 part of line3,383 lb

Each figure is rounded to the pound, so the column can be off by one.

On 3/8" XIP cable at 5:1, with a 3,020 lb working load limit, that's 112%: over the limit. Doubling the line through a snatch block brings it to 1,845 lb per line (61%), and 1/2" XIP cable, with a 5,320 lb limit, brings it to 64%. A 10,000 lb winch is at 34% either way.

Ground and condition factors

Resistance as a percent of the casualty's weight. These are standard recovery planning factors.

ConditionFactor
Hard surface: asphalt, hard-packed5%
Soft or rough: grass, gravel15%
Wheels won't turn: locked, damaged, no wheels67% (two-thirds)
Mired to the hub100%
Mired over the hub, below the fender200%
Mired over the fender, up to the body300%

Wire rope working load limits

Typical minimum breaking strength of new 6x19 class bright wire rope, and the working load limit at a 5:1 design factor. The tag or certificate on your own rope governs.

DiameterXIP / EIPS, IWRCIPS, IWRC
BreakingWLL 5:1BreakingWLL 5:1
1/4"6,8001,3605,8801,176
5/16"10,5402,1089,1601,832
3/8"15,1003,02013,1202,624
7/16"20,4004,08017,7803,556
1/2"26,6005,32023,0004,600
9/16"33,6006,72029,0005,800
5/8"41,2008,240——
3/4"58,80011,760——
7/8"79,60015,920——
1"103,40020,680——

Pounds. WLL is the breaking strength divided by the design factor.

Common questions

Why doesn't doubling the line cut the pull in half?
The snatch block is another sheave, so the total goes up by 10% before it's split between the two lines.
Degrees or percent grade?
Either. The calculator converts between them: 5° is about 8.7% grade, and 45° is a 100% grade.
Is it free? Is my job sent anywhere?
It's free, with no sign-up. Everything runs in your browser, and what you enter stays on your device.

Made by Tahuya River Software

WinchPull is a free tool from Tahuya River Software, LLC. We build custom software for the everyday work of running a business, when off-the-shelf tools don't fit. Built by people who do the work.

Visit tahuyariver.com

How it's calculated. Grade = weight × sin(angle). Resistance = weight × cos(angle) × the ground factor. Sheave friction = 10% of that load for each sheave. Line tension = total ÷ parts of line.

Factors. Hard surface 5%, soft or rough surface 15% and wheels that won't turn 2/3 are the standard planning factors used across towing and recovery. Cable working load limit defaults to one-fifth of breaking strength (a 5:1 design factor). Breaking strengths are typical manufacturer catalog values for new 6x19 class bright wire rope; the tag or certificate on your own rope governs. Mire factors and sheave friction follow US Army ATP 4-31, Recovery and Battle Damage Assessment and Repair, a public-domain publication (copy). Worn, kinked or damaged rope is weaker than any chart shows.

Limits. Results are planning estimates, not measurements. Ground conditions and tires vary, and a line pulled at an angle to the slope or a shock load puts more on the line than shown. Not affiliated with or endorsed by the US Army or any training organization.